The Cherub GT-4 is a 4 band EQ with Chromatic tuner, feedback-fighting notch and phase effect. The visible portion of GT-4 is only 52mm x 54mm x 4mm. Low battery message will be displayed when the battery is getting low. FEATURES: 3 band EQ Chromatic Tuner Feedback-fighting Notch Filter Phase Mid Frequency Control Low Battery Check LED Includes Piezo Ceramic Pick-up SPECIFICATIONS: Input impedance: 10MΩ Frequency Response: 20Hz - 20kHz Control Range: Low ±12dB at 100Hz / Middle ±12dB at 250Hz-10kHz / High ±12dB at 6kHz Pick-up: Piezo Ceramic Pick-up Output jack: 6.35mm Battery Life: Over 100 hours Power Supply: 9V Alkaline Battery Dimensions (L x W): 54mm x 52mm
The Cherub GT-6 is an acoustic guitar preamp featuring a 4 Band EQ with built-in highly accurate chromatic tuner. It has phase, reverb, delay, chrous and wide effects. The compact size makes it easy to install into a guitar and the visible portion is only 52mm x 54mm x 4mm. Low battery message is displayed when the battery is getting low. FEATURES: 3 band EQ + Mid Frequency Control Chromatic Tuner Phase, Reverb, Delay, Chorus & Wide FX Low Battery Check LED Includes Piezo Cable Pick-up SPECIFICATIONS: Input impedance: 10MΩ Frequency Response: 20Hz - 20kHz Control Range: Low ±12dB at 100Hz / Middle ±12dB at 1.5kHz / High ±12dB at 3kHz Pick-up: Piezo Cable Pick-up Output jack: 6.35mm Battery Life: Over 15 hours Power Supply: 9V Alkaline Battery Dimensions (L x W): 54mm x 52mm
The Headway EDB-2 boasts Refined Class “A” Inputs and Pro Audio IC Components, easy to read Pro-Audio design layout & sturdy metal housings built to withstand “Life on the Road”. The EDB-2 is supplied with belt clips, rubber feet and is threaded for microphone stands. “The Swiss Army Knife for the gigging musician.” Comprehensively packed with practical and effective sound crafting features: Twin channel with individual inputs & gain controls 5 Band EQ assignable to Channel 1, 2 or both Notch Filter assignable to Channel 1 or 2 Huge 0-32 dB Gain to interface with most mixers/desks etc Phantom Power is assignable to either "ring", "tip", or XLR to power virtually all instrument microphones/pickups. Phase Reverse assignable t each channel Earth Lift Switch "Range" Switch tuned for specific instruments i.e. Violin, Guitar, Bass etc iPod Input for backing tracks, practice routines etc Mute Switch Mono, Stereo & XLR Inputs, Jack and XLR Outputs Battery or Mains powered (power supply included)
Serious equipment for serious musicians made simple. A gigging musician playing any acoustic instrument will know the difficulties in reproducing the sonic qualities at a cafe or pub gig, that sounded so great at home. The EDM-1 Acoustic Pre-Amp solves these problems by taking the signal from the intruments’ pickup and giving you complete control over the bass, mid and treble, helping to add a richness while acheiving a beautifully clean sound. Control like never before. The Range control is a Hi-Pass filter that has settings for several different instruments including; Rock Acoustic (300Hz), Ukulele, Violin/Mandolin, Viola, Tenor G, Bouzouki, Guitar (80Hz), Low D Guitar, Cello, Baritone and Bass. Able to be mounted on a belt clip or screwed onto a mic stand, the EDM-1 is built into a sturdy metal casing which comes with a set of batteries and rubber feet. The EDM-1 is an essential piece of kit for acoustic players - solo, duet or in a small band - who need to keep a handle over their sound and deliever an authentic acoustic tone to the masses. The EDM-1 Specs: • 3 Band EQ • Tuneable “Range” Control covers all instruments • 9v Phantom Power assignable to “Ring” or “Tip” • XLR Adaptor included - Converts Output Jack to XLR Balanced DI Out • 3 Way Impedance Selector • Earth Lift Switch • Mute Switch • Battery, Mains (adapter optional) or Phantom Powered
What makes the Pure XLR Mach 2 Preamp sound so good? The circuit runs on a “voltage doubler” that provides 18 volts to the internal components even though it uses standard 9 volt input voltage. The result is high-powered clarity that simply cannot be achieved with a regular 9-volt circuit! Electronic circuits work more efficient on higher power and electronic components designed for low power consumption will never sound as good as the more power-hungry components that are optimized for tone quality. There is a direct relation between power consumption and sound quality, meaning that preamps with 200+ hours battery life will compromise on sound quality. Phantom powered preamps, depending on their complexity, also need to compromise on power consumption issues as phantom power fluctuates and diminishes with the number of consumers connected. Generally, low power consumption equals less high-end response, less headroom (circuit peaks or overloads sooner), and less overall clarity. At K&K, we've always favored sound quality over power consumption in our external preamp line, but with the Pure XLR Mach 2 Preamp we went even further and run it on 18 volts. This feature alone would make the new Pure XLR Mach 2 Preamp worthwhile, but we added a few more things that players have asked for: +/- 15dB Parametric band that covers 150Hz to 700Hz with adjustable notch width Full bypass of parametric stage if not needed Tuner output Mute switch input In addition to these features: Proprietary K&K high-power three band EQ (bass – mid – treble) Adjustable input gain Phase switch Master volume Simultaneously usable 1/4” line out and balanced XLR – DI output The tuner output allows you to connect your tuner “open ended," so there will be no signal degradation by passing through it and no switch noise. The Pure XLR Mach 2 Preamp preserves harmonics and overtones and provides a more open and true acoustic sound response. The additional parametric band allows you to fine-adjust the low mid / high bass band for optimum tone and feedback control. We know our customers want the best and truest acoustic tone and we are proud to introduce this new preamp. We believe it brings out the best!
The Martin Thinline The Active Jack will give active performance to your existing Thinline 332 pickup or any piezo or magnetic pickup without additional modification. State-of-the-art circuitry is housed in the jack's shielding cap. The Thinline Active jack will give you more than 12,000 hours of life from one 9V battery.
Flagship - Sounds you never thought possible With this new and groundbreaking Class A preamp your music has never sounded better. Clear smooth highs, soulful mids and bodacious bass combined with an impressive dynamic range of 115dB will lead your inspiration to new levels.With a true bandwidth of 1Hz to 20kHz at +/- 0 dB our state-of-the-art FlagShip circuitry provides unprecedented signal fidelity along with exceptional operational convenience.And because of FlagShip‘s leading-edge Rail to Rail technology a single 9V alcaline battery will provide you with 1.000+ hours of play time.Enjoy a self-sensing circuitry automatically switching in mono- or stereo-operation respectively by sensing which kind of chord you plugged in. In addition the FlagShip preamp offers an ultra-silent operation with a signal to noise-ratio of -115dB and a noise floor of just 20 dBV while Schaller‘s own FlagShip gold-contact 5-way Megaswitch lets you choose from a vast variety of piezo and magnetic switching-options and –combinations never seen in any preamp before.SoundInnovationPerformance Suitable for all piezo-pickup systems plug & play solderfree connections5-Way Megaswitch Switching Options in Mono- and in Stereo-Mode:Mono and stereo positions 2 through 5 feature identical controls and functions allowing for a transparent layout and easy handling. Pos 1 Mono and Pos 1 Stereo feature special utility settings.Pos 1 mono: piezo raw-mode (1) / stereo: mute, silent-mode (2)Pos 2 piezo into FlagShip preampPos 3 magnetic pickups and piezo signal into FlagShip preampPos 4 magnetic pickups into FlagShip preamp (buffered)Pos 5 magnetic pickups pure and unaltered (hardwire-bypass)(1) for reference purposes use this option to hear the raw piezo signal(2) when playing live use this option for silently changing instruments3-Way rotary switch Switching Options in Mono- and Stereo-Mode:The mono and stereo switching positions 2, 3 and 5 feature identical controls and switching functions for user-friendly layout.MONOPos 2 acoustic activePos 3 magnetic + acoustic activePos 5 magnetic bypassSTEREOPos 2 acoustic activePos 3 magnetic + acoustic activePos 5 magnetic bypassFeatures, Specifications & Benefits Advanced class A circuitry for sweet,transparent sound Compact, robust and perfectly shielded Attractive and protective casing with see-through window Original Schaller gold-contact 5-way Megaswitch for outstanding signal flow and switching options Stereo/mono selfsensing and –adjusting circuitry (no extra switch required) Rail to Rail energy effi ciency technology Reverse polarity and static discharge circuit protection Automatic power shut-off when cable is disconnected Plug-in contacts for easy solderfree installation 1000+ hours of playtime on a single 9V alcaline battery True 1Hz - 20kHz bandwidth at +/-0 dB Ultra quiet -115 dB signal to noise-ratio Input impedance: magnetic 3 megohms / piezo 1 megohm Output impedance: 5 megohms All parts and components 100% made in Germany Comes complete with 5-way Megaswitch, mono-/stereo-jack, Schaller control potentiometer (22K-Ohm), wiring and plugs Weight in gramms: 49 Size in mm: 89 x 24 x 7(all specifications subject to change without notice)Volume piezo bridge and passive pickup with variable adjustment.Supplied with a stereo jack socket. This allows the piezo and pickup signal to be separated using a stereo splitter y-cable and then connected to two different amps or channels.Caution: When a connection is made to pickups that are already live, the output signal increases automatically!A 9 volt battery can be used as a general power supply.Please note that piezo bridges are not earthed.A comprehensive instruction and installation guide with additional detailed information and illustrations are available to download on our webseite under products/product help/flagship. Quick 10 Step Guide to FlagShip01. signal to noise ratioratio describing the level of signal to the level of background noise in dB (higher is better)02. dynamic rangemeasured gap from the loudest possible undistorted signal amplitude to the most quiet one in dB (higher is better)03. bandwidthspan between the lowest (here 1 Hz) and the highest frequency (here 20 kHz) the preamp can linearly (meaning without distortion) amplify or reproduce04. noise floorsignal created from the sum of all noise sources (lower is better)05. hardwire-bypass or true bypasspure and unaltered guitar signal by way of bypassing any form of active signal-processing06. reverse polarity protectioncircuitry protecting the electronic components from interchanging plus and minus polarity (here: protection from interchanging the +poles and -poles of the battery)07. static discharge protectioncircuitry protecting the electronic components from an electrical voltage spark or 'spike'08. piezo pickuppiezo-electrical signal created by transforming pressure/vibration into output voltage09. magnetic pickupmagnetic pickup signal is created by transforming string motion and magnetic resistance into output voltage10. buffered signalhigh impedance signal transformed into a low impedance signal, therefore unaffected by high capacitance of excessive signal-cable and/or patch-cable lengthsAnother significant benefit of switching pos 4. is the buffered signal, i.e. the conversion of the high capacity passive pickup signal into a low capacity active pickup signal. This prevents sound degradation commonly associated with running extended cable lengths or using inferiour cable qualities. Your magnetic pickup signal will remain strong, clear and detailed even on the most unfavourable conditions.(see: Quick 10 Step Guide to FlagShip) Schaller Flagship preamp – Stereo / Mono OperationFor mono and for stereo use the Flagship preamp features an advanced mono / stereo selfsensing output stage. The Flagship preamp senses whether a mono 1/4“ or a stereo 1/4“ plug is inserted and switches into the appropriate mode automatically. Not only does this prevent misuse so commonly known from mono/stereo toggle switches. It also allows for just one output jack (see stereo jack enclosed) in your guitar to operate the Flagship to its fullest potential.In mono mode the sound of the magnetic pickups is mixed with the sound of the piezo pickups within the preamp. We recommend using a regular 1/4“ plug guitar cable. Please refer to the Flagship manual for all dedicated sound options in this mode.In stereo mode the sound of the magnetic pickups and the sound of the piezo pickups are sent seperately to the stereo output jack. Please refer to the Flagship manual for all dedicated sound options in this mode.We recommend two ways for routing the signals:1. Using a stereo cable with two 1/4“ plugs for routing the magnetic and piezo signal seperately to a mixing console’s stereo input.2. Using a Y-cable with two 1/4“ mono plugs and one 1/4“ stereo plug for splitting your signal between a guitar amp for the magnetic pickups and a PA or acoustic amp for the piezo signal.The stereo and mono plugs should be connected as follows:Tip of stereo plug goes to tip of mono plug left.Ring of stereo plug goes to tip of mono plug right.Sleeve of stereo plug goes to sleeve of mono plug left.Sleeve of stereo plug goes to sleeve of mono plug right.Please note that by connecting the grounds of two amps or an amp with a PA a low-frequency ground hum may occur. This is an inherent problem caused by ground loops and in no way a fault within the Flagship preamp.
Flagship - Sounds you never thought possible With this new and groundbreaking Class A preamp your music has never sounded better. Clear smooth highs, soulful mids and bodacious bass combined with an impressive dynamic range of 115dB will lead your inspiration to new levels.With a true bandwidth of 1Hz to 20kHz at +/- 0 dB our state-of-the-art FlagShip circuitry provides unprecedented signal fidelity along with exceptional operational convenience.And because of FlagShip‘s leading-edge Rail to Rail technology a single 9V alcaline battery will provide you with 1.000+ hours of play time.Enjoy a self-sensing circuitry automatically switching in mono- or stereo-operation respectively by sensing which kind of chord you plugged in. In addition the FlagShip preamp offers an ultra-silent operation with a signal to noise-ratio of -115dB and a noise floor of just 20 dBV while Schaller‘s own FlagShip gold-contact 5-way Megaswitch lets you choose from a vast variety of piezo and magnetic switching-options and –combinations never seen in any preamp before.SoundInnovationPerformance Suitable for all piezo-pickup systems plug & play solderfree connections5-Way Megaswitch Switching Options in Mono- and in Stereo-Mode:Mono and stereo positions 2 through 5 feature identical controls and functions allowing for a transparent layout and easy handling. Pos 1 Mono and Pos 1 Stereo feature special utility settings.Pos 1 mono: piezo raw-mode (1) / stereo: mute, silent-mode (2)Pos 2 piezo into FlagShip preampPos 3 magnetic pickups and piezo signal into FlagShip preampPos 4 magnetic pickups into FlagShip preamp (buffered)Pos 5 magnetic pickups pure and unaltered (hardwire-bypass)(1) for reference purposes use this option to hear the raw piezo signal(2) when playing live use this option for silently changing instruments3-Way rotary switch Switching Options in Mono- and Stereo-Mode:The mono and stereo switching positions 2, 3 and 5 feature identical controls and switching functions for user-friendly layout.MONOPos 2 acoustic activePos 3 magnetic + acoustic activePos 5 magnetic bypassSTEREOPos 2 acoustic activePos 3 magnetic + acoustic activePos 5 magnetic bypassFeatures, Specifications & Benefits Advanced class A circuitry for sweet,transparent sound Compact, robust and perfectly shielded Attractive and protective casing with see-through window Original Schaller gold-contact 5-way Megaswitch for outstanding signal flow and switching options Stereo/mono selfsensing and –adjusting circuitry (no extra switch required) Rail to Rail energy effi ciency technology Reverse polarity and static discharge circuit protection Automatic power shut-off when cable is disconnected Plug-in contacts for easy solderfree installation 1000+ hours of playtime on a single 9V alcaline battery True 1Hz - 20kHz bandwidth at +/-0 dB Ultra quiet -115 dB signal to noise-ratio Input impedance: magnetic 3 megohms / piezo 1 megohm Output impedance: 5 megohms All parts and components 100% made in Germany Comes complete with 5-way Megaswitch, mono-/stereo-jack, Schaller control potentiometer (22K-Ohm), wiring and plugs Weight in gramms: 49 Size in mm: 89 x 24 x 7(all specifications subject to change without notice)Volume piezo bridge and passive pickup with variable adjustment.Supplied with a stereo jack socket. This allows the piezo and pickup signal to be separated using a stereo splitter y-cable and then connected to two different amps or channels.Caution: When a connection is made to pickups that are already live, the output signal increases automatically!A 9 volt battery can be used as a general power supply.Please note that piezo bridges are not earthed.A comprehensive instruction and installation guide with additional detailed information and illustrations are available to download on our webseite under products/product help/flagship. Quick 10 Step Guide to FlagShip01. signal to noise ratioratio describing the level of signal to the level of background noise in dB (higher is better)02. dynamic rangemeasured gap from the loudest possible undistorted signal amplitude to the most quiet one in dB (higher is better)03. bandwidthspan between the lowest (here 1 Hz) and the highest frequency (here 20 kHz) the preamp can linearly (meaning without distortion) amplify or reproduce04. noise floorsignal created from the sum of all noise sources (lower is better)05. hardwire-bypass or true bypasspure and unaltered guitar signal by way of bypassing any form of active signal-processing06. reverse polarity protectioncircuitry protecting the electronic components from interchanging plus and minus polarity (here: protection from interchanging the +poles and -poles of the battery)07. static discharge protectioncircuitry protecting the electronic components from an electrical voltage spark or 'spike'08. piezo pickuppiezo-electrical signal created by transforming pressure/vibration into output voltage09. magnetic pickupmagnetic pickup signal is created by transforming string motion and magnetic resistance into output voltage10. buffered signalhigh impedance signal transformed into a low impedance signal, therefore unaffected by high capacitance of excessive signal-cable and/or patch-cable lengthsAnother significant benefit of switching pos 4. is the buffered signal, i.e. the conversion of the high capacity passive pickup signal into a low capacity active pickup signal. This prevents sound degradation commonly associated with running extended cable lengths or using inferiour cable qualities. Your magnetic pickup signal will remain strong, clear and detailed even on the most unfavourable conditions.(see: Quick 10 Step Guide to FlagShip) Schaller Flagship preamp – Stereo / Mono OperationFor mono and for stereo use the Flagship preamp features an advanced mono / stereo selfsensing output stage. The Flagship preamp senses whether a mono 1/4“ or a stereo 1/4“ plug is inserted and switches into the appropriate mode automatically. Not only does this prevent misuse so commonly known from mono/stereo toggle switches. It also allows for just one output jack (see stereo jack enclosed) in your guitar to operate the Flagship to its fullest potential.In mono mode the sound of the magnetic pickups is mixed with the sound of the piezo pickups within the preamp. We recommend using a regular 1/4“ plug guitar cable. Please refer to the Flagship manual for all dedicated sound options in this mode.In stereo mode the sound of the magnetic pickups and the sound of the piezo pickups are sent seperately to the stereo output jack. Please refer to the Flagship manual for all dedicated sound options in this mode.We recommend two ways for routing the signals:1. Using a stereo cable with two 1/4“ plugs for routing the magnetic and piezo signal seperately to a mixing console’s stereo input.2. Using a Y-cable with two 1/4“ mono plugs and one 1/4“ stereo plug for splitting your signal between a guitar amp for the magnetic pickups and a PA or acoustic amp for the piezo signal.The stereo and mono plugs should be connected as follows:Tip of stereo plug goes to tip of mono plug left.Ring of stereo plug goes to tip of mono plug right.Sleeve of stereo plug goes to sleeve of mono plug left.Sleeve of stereo plug goes to sleeve of mono plug right.Please note that by connecting the grounds of two amps or an amp with a PA a low-frequency ground hum may occur. This is an inherent problem caused by ground loops and in no way a fault within the Flagship preamp.
Copyright © 2024 BC Wholesalers
